GM215 - Multi-mode Step Motor Controller The GM215 is a stepper drive with a full motion controller. 15 operating modes include Motion Control, stand-alone control and sub-micro stepping for the smoothest possible operation of your stepper motor. Midband resonance compensation Motor smoothness, ARC Damping and VCO trim pots Terminal block 12-position 5mm Full motion controller with non-volatile memory Capable of running as a standalone solution Hard anodized electrically isolated heatsink Maximum power dissipation of 13W Recommended for NEMA 17-42 size motors DIP switch settable current and option adjust

G901X - Step Pulse Multiplier The G901X is a step pulse multiplier for G201X (Stock-no. 793-4127) and G203V (Stock-no. 793-4121) Digital Stepper Drives. Allows base drive to run in full step, half step, 5μStep or 10μStep modes. Jumper for setting the mode

G203V - Stepper Drive The G203V is the new generation CPLD-based microstep drive. It has short-circuit protection for the motor outputs, over-voltage and under-voltage protection, over-temperature protection, reversed power supply polarity protection and will survive accidental motor disconnects while powered-up. The “V” in G203V stands for “Vampire” as it is an unkillable drive. The G203V uses a synchronous PWM design that is absolutely silent when the motor is stopped or turning slowly. It virtually eliminates stopped-motor heating regardless of power supply voltage. The G203V is a jumper-free drive. There are no internal user settings at all so there is no need to ever remove the drive cover at all. STEP, DIRECTION and DISABLE inputs are opto-isolated These inputs are +2.5/3.3/5 VDC compatible Direction is clocked in on the active step pulse edge Needs heatsinking for current settings greater than 3 amps LED-status indicators Power supply voltage between 15 and 80 VDC

G201X - Step Motor Drive The G201X is a stepper motor drive with an aluminium case. Drives stepper motors up to 7 Amps. STEP and DIRECTION inputs are +3.3/5 VDC compatible Recirculate mode during STANDBY greatly reduces motor heating while stopped Power-on RESET Direction is clocked in on the active step pulse edge DIP switch settings for current and motor version Needs heatsinking for current settings greater than 3 amps Low motor heating while stopped Power supply voltage between 18 and 80 VDC Aluminium cover and plate Connector type is Modular, 5mm pitch

GM215 - Multi-mode Step Motor Controller The GM215 is a stepper drive with a full motion controller. 15 operating modes include Motion Control, stand-alone control and sub-micro stepping for the smoothest possible operation of your stepper motor. Midband resonance compensation Motor smoothness, ARC Damping and VCO trim pots Terminal block 12-position 5mm Full motion controller with non-volatile memory Capable of running as a standalone solution Hard anodized electrically isolated heatsink Maximum power dissipation of 13W Recommended for NEMA 17-42 size motors DIP switch settable current and option adjust

G901X - Step Pulse Multiplier The G901X is a step pulse multiplier for G201X (Stock-no. 793-4127) and G203V (Stock-no. 793-4121) Digital Stepper Drives. Allows base drive to run in full step, half step, 5μStep or 10μStep modes. Jumper for setting the mode

G203V - Stepper Drive The G203V is the new generation CPLD-based microstep drive. It has short-circuit protection for the motor outputs, over-voltage and under-voltage protection, over-temperature protection, reversed power supply polarity protection and will survive accidental motor disconnects while powered-up. The “V” in G203V stands for “Vampire” as it is an unkillable drive. The G203V uses a synchronous PWM design that is absolutely silent when the motor is stopped or turning slowly. It virtually eliminates stopped-motor heating regardless of power supply voltage. The G203V is a jumper-free drive. There are no internal user settings at all so there is no need to ever remove the drive cover at all. STEP, DIRECTION and DISABLE inputs are opto-isolated These inputs are +2.5/3.3/5 VDC compatible Direction is clocked in on the active step pulse edge Needs heatsinking for current settings greater than 3 amps LED-status indicators Power supply voltage between 15 and 80 VDC

G201X - Step Motor Drive The G201X is a stepper motor drive with an aluminium case. Drives stepper motors up to 7 Amps. STEP and DIRECTION inputs are +3.3/5 VDC compatible Recirculate mode during STANDBY greatly reduces motor heating while stopped Power-on RESET Direction is clocked in on the active step pulse edge DIP switch settings for current and motor version Needs heatsinking for current settings greater than 3 amps Low motor heating while stopped Power supply voltage between 18 and 80 VDC Aluminium cover and plate Connector type is Modular, 5mm pitch