Flow Switches

New items

FCS-G1/4A4-NA-H1141, Turck

Insertion Flow Sensor (without control logic) Requires a remote signal processor to operate, see stock no 313-2526 or 313-2532 (Available in most markets) Pressure rating up to 60 bar static; 100 bar dynamic Fluid temperature range: –25 to +80°C (100°C for 10 minutes maximum) On delay time: 8s typical Switch on time: 2s Response time: 12s maximum Stainless steel housing Ingress protection to IP67 M12, four-pin plug Flow rates: 1 to150cm 3 /s (water); 3 to 300cm 3 /s (oil); 2 to 30m 3 /s (air)

Product Detail

New items

LFS-04, Cynergy3

Paddle Flow Switch - LFS Series The LFS range of flow switches are paddle devices that are mounted vertically through a socket or upstand process connection. Electrical connections are made within the housing, which has a screw on sealed lid and cable gland. A choice of paddle sizes is supplied with each switch. Higher temperature versions are designated by "H" in the part number. Features and Benefits Stainless steel SS 304 paddle G3/4"" or 1""NPT mounting plug thread Aluminium alloy housing or DIN 43650 plug Maximum operating pressure 20 bar Operating pressure up to 150°C (H versions)

Product Detail

New items

FSP10A30, Cynergy3

FSP10 Flow Switch The FSP10 Flow Switch is an electric pump that can provide increased flow within gravity fed water systems. The FSP10 flow switch is placed in a pipe above the pump and automatically starts at a specified flow rate. The pump turns off automatically when the flow reduces or if the tank empties. Features and Benefits Direct switching of pumps up to 4A inductive 0.6 L/min or 3.0 L/min turn on flow rate Automatic shut down on flow stop Supply and pump electrical connections terminated within case with cable glands at entry 1"" BSP pipe connections Note Each model number has a 'on flow rate' please check the datasheet to make sure the part meets your requirements.

Product Detail

New items

FSVPLC30, Cynergy3

FSVPLC Inline Flow Switch The FSVPLC can be used to control some other equipment or process via a PLC. If used in a pumped system, the device has to be fitted in the pipe above the pump. The FSVPLC gives a closed contact signal to the PLC once the flow rate exceeds 0.6 L/min or 3.0 L/min, depending on version. Features and Benefits Signal level output to PLC 0.6 L/min or 3.0 L/min turn on flow rate Automatic shut down on flow stop G1"" pipe connection

Product Detail

New items

RS_256-578, Novotech Controls

High Power Flow Switch SPCO flow switches capable of switching 16A at 240Vac (resistive load). Designed for use within water but can be used with alkalis, alcohol, fuels and lubricating oils. This flow switch should be mounted in line with the flow. Pressure rating 10 bar Flow rate range: 3 to 6 l/min. (set at 4.5) Suitable for use with water, alkalis, alcohols, most fuels and mineral based lubricating oils Operating temperature: 70°C maximum Wetted materials approval in accordance with UK Water Fittings and Bylaws scheme (WFBS) listed Note Not designed for frequent flow rate readjustment. Not for use with diluted or concentrated acids. Supplied with compression fittings and 1m of three-core PVC cable fitted.

Product Detail

New items

FCS-G1/2A4-NA-H1141, Turck

Insertion Flow Sensor (without control logic) Requires a remote signal processor to operate, see stock no 313-2526 or 313-2532 (Available in most markets) Pressure rating up to 60 bar static; 100 bar dynamic Fluid temperature range: –25 to +80°C (100°C for 10 minutes maximum) On delay time: 8s typical Switch on time: 2s Response time: 12s maximum Stainless steel housing Ingress protection to IP67 M12, four-pin plug Flow rates: 1 to150cm 3 /s (water); 3 to 300cm 3 /s (oil); 2 to 30m 3 /s (air)

Product Detail

New items

FSVPLC06, Cynergy3

FSVPLC Inline Flow Switch The FSVPLC can be used to control some other equipment or process via a PLC. If used in a pumped system, the device has to be fitted in the pipe above the pump. The FSVPLC gives a closed contact signal to the PLC once the flow rate exceeds 0.6 L/min or 3.0 L/min, depending on version. Features and Benefits Signal level output to PLC 0.6 L/min or 3.0 L/min turn on flow rate Automatic shut down on flow stop G1"" pipe connection

Product Detail

New items

FCS-GL1/2A4-NA-H1141, Turck

Insertion Flow Sensor (without control logic) Requires a remote signal processor to operate, see stock no 313-2526 or 313-2532 (Available in most markets) Pressure rating up to 60 bar static; 100 bar dynamic Fluid temperature range: –25 to +80°C (100°C for 10 minutes maximum) On delay time: 8s typical Switch on time: 2s Response time: 12s maximum Stainless steel housing Ingress protection to IP67 M12, four-pin plug Flow rates: 1 to150cm 3 /s (water); 3 to 300cm 3 /s (oil); 2 to 30m 3 /s (air)

Product Detail

New items

510-0565, RS PRO

Piston Flow Switch Monitoring of low flow rates of liquids. A piston equipped with a magnet is displaced by the flow, this action is proportional to the flow rate against a supporting spring. A reed switch on the outside is positioned at the desired point within the control range. A signal is generated when the actual flow rate value is above or below the set value. High pressure and temperature capabilities Scaled switch point setting Low flow switching capabilities Installation independent of position Material Brass Note If used on air system, life expectancy of the unit is greatly reduced due to instantaneous pressure loss on the piston, which has no damping.

Product Detail

New items

510-0559, RS PRO

Piston Flow Switch Monitoring of low flow rates of liquids. A piston equipped with a magnet is displaced by the flow, this action is proportional to the flow rate against a supporting spring. A reed switch on the outside is positioned at the desired point within the control range. A signal is generated when the actual flow rate value is above or below the set value. High pressure and temperature capabilities Scaled switch point setting Low flow switching capabilities Installation independent of position Material Brass Note If used on air system, life expectancy of the unit is greatly reduced due to instantaneous pressure loss on the piston, which has no damping.

Product Detail

New items

LFS-02, Cynergy3

Paddle Flow Switch - LFS Series The LFS range of flow switches are paddle devices that are mounted vertically through a socket or upstand process connection. Electrical connections are made within the housing, which has a screw on sealed lid and cable gland. A choice of paddle sizes is supplied with each switch. Higher temperature versions are designated by "H" in the part number. Features and Benefits Stainless steel SS 304 paddle G3/4"" or 1""NPT mounting plug thread Aluminium alloy housing or DIN 43650 plug Maximum operating pressure 20 bar Operating pressure up to 150°C (H versions)

Product Detail

New items

510-0571, RS PRO

Piston Flow Switch Monitoring of low flow rates of liquids. A piston equipped with a magnet is displaced by the flow, this action is proportional to the flow rate against a supporting spring. A reed switch on the outside is positioned at the desired point within the control range. A signal is generated when the actual flow rate value is above or below the set value. High pressure and temperature capabilities Scaled switch point setting Low flow switching capabilities Installation independent of position Material Brass Note If used on air system, life expectancy of the unit is greatly reduced due to instantaneous pressure loss on the piston, which has no damping.

Product Detail

New Items

FCS-G1/4A4-NA-H1141, Turck

LFS-04, Cynergy3

FSP10A30, Cynergy3

FSVPLC30, Cynergy3

RS_256-578, Novotech Controls

FCS-G1/2A4-NA-H1141, Turck

FSVPLC06, Cynergy3

FCS-GL1/2A4-NA-H1141, Turck

510-0565, RS PRO

510-0559, RS PRO

LFS-02, Cynergy3

510-0571, RS PRO

FAQs